Feeds:
Posts
Comments

Posts Tagged ‘Bamboo fly rod’

I have made the next steps for the wooden rod tube… glued up, sanded and sealed… next is to cap the end with a thin hardwood ply, sand and seal them to form a complete sealed tube. Once dry and ready I will then cut about an inch & half down from one end to fit a wee brass hinge and probably a small magnet or maybe some sort of leather closer???

 

wooden rod tube-4

wooden rod tube

wooden rod tube-2

 

Plan is to try and have this done this week ready for traveling to Southland for opening, something to protect my Bamboo rod in transit to a special wee stream I have in mind!

Read Full Post »

I have made a start on a hexagonal wooden rod tube for the bamboo rod, it will be nice to have something a little different to keep the rod safe. I collected some hardwood slats back while I still worked at ITM, they had small wood worm marks that I thought would create a cool old recycled look to the tube. Richard (Pedigree Drums) my brother in-law has a pretty sweet workshop so I cheated and dropped the timber to him to machine, that way I knew the angles would be correct and accurate rather than my builders technique of a rough old rip saw and plenty of sanding.

 

wooden rod tube

 

I plan to varnish the finished tube with the same Spar varnish I coated the boo blank with, I have coated the inside of the slats prior to gluing it up to seal and protect the inside of the rod tube. I got a little more varnish on the edges than intend so I will have a bit of clean up before I glue it up. Pretty happy with the colour and grain that has come out with the varnish…

 

wooden rod tube-2

wooden rod tube-3

 

Once dried, a quick sand and scrap the edges, it will be time to glue up and sand down for the outside to be varnished… keep tuned!

 

Read Full Post »

I finished the bamboo build and finally got a chance to fish it… I’m loving it! Matt from Iconoclast Fly Rods has built a fantastic taper… all I did was give him a few points I wanted the rod to do and he hit it on the head. The taper is faster than the demo model he sent with just the right amount of stiffness to the butt section, it’s going to be a fantastic rod on some wee Southland streams this season.

I went up the top of the lake today with my brother to fish the rod (was good timing to have a photographer on hand, thanks bro!)… first cast and I was impressed, very impressed. It presents well and feels great with a fish on, it wasn’t the biggest of fish first up but felt lively playing the fish while having the feel of power to drag in any good fish. I look forward to targeting a few willow grubbing trout this season with it!

 

Bamboo christened-2

Bamboo christened

Bamboo christened-3

 

Unintentional middle finger photo… not sure how I did this one???

 

I have to give a huge thanks to Matt at Iconoclast Fly rods, he has built a fantastic rod… it does exactly what I asked him for it to do. All I need now is to make the hexagonal wooden rod tube and a rod sock, got the fabric and my brother in-law is machining the timber this week, the project nears an end.

Read Full Post »

Holiday break has given me some time to potter on the boo, I’ve fitted and glued the grip and wrapped the bamboo female ferrules on the two tip sections. I also put a first coat on the wraps to secure them before I start the guide wraps…

 

Bamboo build-5

Grip and Reel seat all glued up…

 

Bamboo build-6

About half way on the first Ferrule wrap…

 

Bamboo build-7

Ferrule wrap ready to coat…

 

Bamboo build-8

Both tip section Ferrules wrapped and first coated, drying…

 

Bamboo build-10

Hook keep wrapped and coated…

 

Will let these fully dry before I move to the next step, I have the guide spacing marked on the bench ready to start marking out and wrapping the guides.

Read Full Post »

The reel seat arrived from the US today, I ordered a couple to save on freight… it just means I need to build another rod after this one…

Bamboo build-2

Checking out the two options I ordered…

Bamboo build-3

I chose the bamboo reel seat, it’s a bit darker in colour but looks good all the same…

Reel Seat all glued up now so no changing my mind now!!

 

 

 

Read Full Post »

Matt is working on the finishing touches for the second tip section currently but posted these pics of the tip fitted with the ferrule to the butt section…

007_zpse3e5c614

013_zpsbd5cda21014_zps257fdc4e015_zps9e7834a1

Busy time ahead building rods I thinkā€¦ now what thread and reel seat to use????

Read Full Post »